腐蚀对模块式钢结构选煤厂设备支架振动响应影响的测试及分析

选煤厂采用模块式钢结构作为设备支架,受设备使用及养护不当造成结构构件严重腐蚀,构件截面削弱,导致结构产生过大振动,通过对结构各层振动响应测试,得到各测点水平向及竖直向振动速度幅值。经分析得出腐蚀后对结构整体刚度影响程度,为后期采取措施及安全生产提供依据。     

Cutting parameter optimization for one-step shaft excavation technique based on parallel cutting method

The outcome of the cutting blasting in a one-step shaft excavation is heavily related to the cutting parameters used for parallel cutting method. In this study, the relationships between the cutting parameters (such as the hole spacing L and the empty hole diameter D) and damage zones were investigated by numerical simulation. A damage state index γ was introduced and used to characterize the crushing and crack damage zones through a user-defined subroutine. Two indices, i.e., η₁ and η₂ that can reflect the cutting performance, were also introduced. The simulation results indicate that an optimal value of L can be obtained so that the η₁ and η₂ can reach their optimal states for the best cutting performance. A larger D results in better cutting performance when the L value maintains its best. In addition, the influences of the loading rate and the in-situ stress on the cutting performance were investigated. It is found that an explosive with a high loading rate is suit for cutting blasting. The propagation direction and the length of the tensile cracks are affected by the direction and the magnitude of the maximum principal stress.     

Structural optimization with an automatic mode identification method for tracking the local vibration mode

Traditional optimization methods, which take a specific order of modal frequency as the design constraint, could fail to obtain the desired solution because of modal substitution. An improved optimization model with continuous sizing variables is established to solve this problem, in which the minimum weight and a given local modal frequency are considered as the objective and the constraint. To capture accurately the expected mode of vibration, a local mode identification technique is proposed based on the strain energy ratio between the local area and the whole structure. With that scheme, an optimization system is developed, in which the local mode can be effectively identified and the constraint can be updated with it in the iteration process. Two numerical examples, of a reinforced plate and a satellite structure, are applied to illustrate the effectiveness and efficacy of the proposed method.     

Solid dispersion adsorbate technique for improved dissolution and flow properties of lurasidone hydrochloride: characterization using 32 factorial design

The aim of the present study was to improve the dissolution and flow properties of lurasidone hydrochloride (LH) by solid dispersion adsorbate (SDA) technique. Solid dispersions (SDs) of LH were prepared by fusion method using Poloxamer P188. The melt dispersion was adsorbed onto the porous carrier Florite (calcium silicate). A 3² factorial design was employed to quantify the effect of two independent variables, namely ratio of carrier (Poloxamer 188) and LH in SD and ratio of adsorbent (Florite) to SD. SDA granules of LH were studied for flow properties and characterized using differential scanning calorimetry, scanning electron microscopy, and X-ray diffraction. Tablets of optimized composition of SDA granules (equivalent to 20?mg of drug) and plain tablets were prepared by direct compression method. The dissolution studies were carried out in Mcllvaine buffer (pH 3.8) as per USFDA guidelines and characterized for parameters such as percent dissolution efficiency, t₅₀, and Q₃₀. Tablets prepared from SDA granules showed almost four-fold increase in cumulative percentage drug release as compared to tablets prepared from plain LH. The value of dissolution efficiency was enhanced from 49.60% for plain tablets to 94.15% for SDA tablets. SDA granules did not show any change in drug release and X-ray diffraction pattern after storage at 40?°C/75% of RH for 3?months, which confirms that Florite prevented conversion of drug from amorphous form to crystalline form improving physical stability of the amorphous state of LH.     

Parallel Multipopulation Differential Evolutionary Particle Swarm Optimization for Voltage and Reactive Power Control

This paper presents parallel multipopulation differential evolutionary particle swarm optimization (DEEPSO) for voltage and reactive power control (VQC). The problem can be formulated as a mixed integer nonlinear optimization problem and various evolutionary computation techniques have been applied to the problem including PSO, differential evolution (DE), and DEEPSO. Since VQC is one of the online controls, speed‐up of computation is required. Moreover, there is still room for improvement in solution quality. This paper applies parallel multipopulation DEEPSO in order to speed up the calculation and improve solution quality. The proposed method is applied to IEEE 30, 57, and 118 bus systems. The results indicate that the proposed method can realize fast computation and minimize more active power losses than the conventional evolutionary computation techniques.     

绿色住区参数化优化设计平台的开发进展与展望

绿色住区设计是建设宜居城市和实现节能减排目标的重要手段与方法。文章首先回顾绿色住区参数化优化设计方法及平台概况，在此基础上，重点介绍平面生成、噪声计算、通风计算、可视度计算等新增功能和天空遮挡算法升级，以及广州市的工程应用，最后展望平台研发与应用的未来发展方向。     

航空发动机进气总温传感器测温误差研究

航空发动机进口总温测量的准确性是优化发动机控制率、保障发动机飞行安全的关键因素之一。针对影响传感器测量准确性的响应时间、恢复系数，通过空气动力学和热力学理论，分析出具体的影响因素，设计了多种结构模型，并通过热风洞试验、FloEFD软件建模和热流体仿真，从材料及结构上系统地提出了优化途径和改善办法并进行了验证，尤其是分析了双余度传感器的响应一致性误差并提出改善方法。研究结果为同类传感器的设计提供了参考和借鉴。